Use a pointed object like a needle or a safety pin to clean out inaccessible areas in the golf iron.Use acrylic spray paintwith the color of your choice to paint the iron. Use a damp paper towel to remove the excess paint. Let the paint dry up. Use two to three coats with enough intervals between each coat for the previous layer to dry.
How to apply paint fill to golf clubs?
How to Apply Paint Fill to Golf Clubs Prepare the golf club by liberally applying a water-based degreasing agent on it. Afterward, clean it well so that when the paint is applied, it sticks on properly. Keep the golf club in a position so that it gets completely dry.
What is the best paint to use on golf clubs?
Enamel paints offer faster drying times and stick on well, making them the best paint to use on golf clubs. Acrylic paints, on the other hand, are not designed to endure the friction that the club is subjected to on the golf course. Use acetone or any paint remover to remove the existing paint from the driver head.
How much does it cost to paint golf clubs?
Painting your set of golf clubs is very affordable to do; usually costing less than $50 USD. So before you think about replacing your clubs, first examine each club and then separate them in 2 piles. Clubs that are damaged or have decreased in performance. Clubs that are looking old, have scratches and scuff marks.
How long does it take for paint to dry on golf clubs?
Allow two hours (or enough time to dry) between the application of each layer of paint. Though some suggest using acrylic paints on golf clubs, I would strongly recommend enamel paints and paints with epoxy mixed in them. Enamel paints offer faster drying times and stick on well, making them the best paint to use on golf clubs.
How to prepare driver head before painting?
How to Prepare your Driver Head before Applying Paint. Use acetone or any paint remover to remove the existing paint from the driver head. Dedicate a good amount of time while using sandpaper on your driver head. Good preparation time will pay off in the long run. Apply a thin layer of etching primer.
What is roughing up metal?
Roughing up: Unprepared metal is hard and has a nonporous surface which does not allow the paint to stick on to it. Consider roughing up the metal surface so that when painted, the paint stays on.
How to remove paint from a putter?
To ensure that your putter is free of paint, grease, and debris, use a toothbrush dipped in dish washing soap and make sure you clean it. Let the putter dry completely. Once it’s completely dry, use a toothpick to apply paint on the putter.
How to put acetone on a putter?
Take a metal bowl and pour acetone into it. Wear gloves made of latex as a precaution before you transfer the acetone. Place your putter in the metal bowl filled with acetone. Make sure all parts of the putter that you want to be painted are submerged well in the acetone.
How to sand a steel shaft?
Sand the steel shaft using sandpaper to prepare it before painting. This will enable the paint to stick on properly. To roughen up graphite shafts, remove the coating at the tip of the shaft. Then use the sandpaper to sand it.
How to use paint remover on golf clubs?
Use a Q-tip to apply generous amounts of paint-remover to the areas of the golf club where you do not want any old paint. Acetone will work well. Wear latex gloves before using acetone.
How to use paint remover?
Apply generous amounts of paint-remover using Q-tip. Acetone will also do the job. Wear latex gloves before using acetone.
How to get rid of acetone on clubhead?
It’s very toxic. When you are finished clean your clubhead with water and ensure all paint debris and acetone are completely gone.
What to use to remove paint spills?
Overflow paint is also okay. You’ll wipe that off later. Ryan Noll. Once dry you can use an acetone-soaked cotton swab to remove excess paint that spilled over the edges. Sometimes you might have to do two or three coats to ensure a good even fill.
How to close a modal window?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button.
What is custom paint fill?
But before we go further, it’s important to know we’re not talking about total paint jobs and we’re definitely not advising you to paint your driver, metal woods or hybrids — rather custom paint fill refers to re-coloring the embossed elements of your clubs such as logos, names and numbers on your irons, wedges and putter. If you’re looking to get a total club makeover, we suggest seeking out a pro for that kind of work. Here’s how you do it.
Can you use acetone to fill in paint?
Now we start painting. I recommend using a needle-tip applicator to fill in your paints, but if that’s not available use a small brush or even a toothpick. The key here is to ensure even, full-paint fills, so if your paint is coming on thick and not filling in the letters or numbers you’re trying to fill, adding acetone can thin it out. It’s also fine if you overfill a little when painting.